Olets Fittings: A Complete Guide - Make Piping Easy (2024)

Piping Fittings and Components

Rehan Ahmad Khan

Share with:


Olets Fittings are also known as (Self Reinforced Forged Fittings, Outlet Fittings, and Branch Connection Fittings). Olets fittings provide a branch connection between the header or run pipe and to the branch or outlet pipe. In other words, you can say Olets fittings are fittings that provide an outlet from a larger pipe to a smaller one (or one of the same size).

The pipe on which Olets fittings are installed is called header/run pipe, and the pipe connected to the other side of Olets fitting is called branch/outlet pipe.

Olets Fittings: A Complete Guide - Make Piping Easy (1)

Table of Contents

Branch Connection Types

Branch connection is not new to us, as we all know standard tee and the fabricated joints (stub in or stub on) have been used for branching. But, the olets fittings have advantages over conventional pipe branch fittings. I am going to describe all the important points in this article, that must be known to the piping professionals.

Olets Fittings: A Complete Guide - Make Piping Easy (2)

Why To Prefer Olets Fittings Over Conventional Branch Connection?

There are many advantages of using Olets fittings over a standard tee and fabricated joint. I have mentioned some of them below-

  • Olets fittings can withstand high-pressure whereas fabricated joints are not preferred for high-pressure line
  • Only 2 welds are needed in Olets fitting whereas for standard tee numbers of the weld are 3
  • It required less installation time
  • Inspection is easy
  • Required less space, which makes the piping system more flexible
  • There is no restriction to flowing fluid, due to the fine design
  • Welding is easy as compared to standard tee
  • It can easily be installed on the pipe rack
  • Reinforcing Pad is not required, as it is self-reinforced fitting
  • Required less material removal from the header or run pipe, which maintains the strength in the header.

We are not going to dig deeper into the other branch connection types, for now, our focus is on Olets fittings. But, a short glimpse was required for clarification and to differentiate the olets fittings and conventional branch connection. Let’s see the main types of olets fittings below-

Olets Fitting Types

Most commonly used Olets fittings types are as follows-

  • Weldolet
  • Sockolet
  • Thredolet
  • Sweepolet
  • Latrolet
  • Flangolet
  • Nipolet
  • Coupolet
  • Elbolet
  • Insert Weldolet
  • Brazolet

Further, we will learn about the design, application and size range of all the most commonly used Olets fittings

Weldolet

Weldolets are the most commonly used among all the olets fittings, and are well-suited for high-pressure applications. A Weldolet makes a 90° branch connection and available in full size or reducing for a straight piece of pipe. It is designed to minimize stress concentrations and provide integral reinforcement, due to its self-enforced design. Weldolet ends are beveled types, and therefore the weldolet is considered a butt-weld fitting.

Olets Fittings: A Complete Guide - Make Piping Easy (3)
  • END – Bevel end
  • Branch Pipe End Bevel end
  • Size Range – 2″ – 24″
  • Most commonly size range used in the industry – 2″ – 8″, (economical size range)
  • Thickness/Schedule – same as the pipe

Sockolet

A Sockolet is the same as Weldolet, with the difference that the branch pipe end will be the plain end, as the Sockolet has socket weld end. Sockolets are used to make a 90° pipe branch. It is used in small size pipe and the line with low-pressure. Fillet welds are used to connect the branch pipe to the Sockolet. On the pipe header side, a Sockolet requires a welded connection same as Weldolet.

Olets Fittings: A Complete Guide - Make Piping Easy (4)
  • END – Socket type
  • Branch Pipe End Plain end
  • Size Range – 1/2″ – 4″
  • Most commonly size range used in the industry – 1/2″ – 2″, (Safe size range)
  • Thickness/Schedule 3000#, 6000# and 9000# (ratings for socketweld fittings)

Thredolet

A Threadolet is similar to a sockolet and weldolet and makes the 90° branch. However, the main difference is the sockolet fitting has a female threaded end, and the branched pipe or Instruments are screwed on the fitting. The branching is possible of the same size or reducing.

Threadolet end is generally NPT type (National Pipe Thread) and comes under Americal standards. The end preparation is done under ASME B1.20.1 specification

Olets Fittings: A Complete Guide - Make Piping Easy (5)
  • END – Female Threaded
  • Branch Pipe End Male threaded
  • Size Range – 1/2″ – 2″
  • Thickness/Schedule 2000#, 3000# and 6000# (ratings for threaded fittings)

Sweepolet

A Sweepolet is a contoured, integrally reinforced, branch connection with a low-stress escalation factor. It has low stresses and long fatigue life.
Okay! getting confused..? Do not worry, I have clarified below-

Olets Fittings: A Complete Guide - Make Piping Easy (6)
  • Where to use – Normally used, if the header is above 24″ NPS and Branch is above 8″ NPS (It is not fixed, it can vary company to company)
  • It is used for reducing pressure drop and for free-draining of fluid
  • Used in radiography requirement
  • END – Bevel end
  • Branch Pipe End Bevel end
  • Size Range – 8″ – 24″ (It is mostly used size range)
  • Thickness/Schedule Same as the pipe/Schedule Number

Latrolet

Latrolet is the only one Olets fittings which provide 45° lateral branch connections, As opposed to the typical 90° branch connection. Latrolets fittings are available with multi-end connections.

Olets Fittings: A Complete Guide - Make Piping Easy (7)
  • END – Female Threaded, Socket Weld, and Bevel end
  • Branch Pipe End Male Threaded, Plain, and Bevel end
  • Size Range – 1/2″ – 2″ NPS (for threaded and socket weld end)
  • Size Range – Above 2″ NPS (for threaded and socket weld end)
  • Thickness/Schedule 3000# and 6000# (for socket and threaded end) , and for Bevel end thickness will be same as pipe or system rating
  • Bevel/butt weld fittings can be used below 2″ NPS (for food, pharma, and corrosive fluid)

Flangolet

Flangolets are the fittings, which are used for joining large-bore header and flanged end components. Breaker flange can also use joined with Flangolet if the line required frequent maintenance.

Olets Fittings: A Complete Guide - Make Piping Easy (8)
  • END – Flanged end
  • Branch component End Flanged end
  • Size Range – 1/2″ – 24″ (Normally available)
  • Rating 150#, 300#, 600#, 900#, 1500#
  • Flange End preparation- ASME B16.5

Nipolet

Nipolets are the fittings, which are used for joining plain end large-bore header and small-bore thread end branch. It is mostly used for valve take-off, high-point vent and low-point drain system. A Nipolet is welded onto the header or run pipe, end is prepared with socket weld or threaded outlets on the branch pipe side.

Olets Fittings: A Complete Guide - Make Piping Easy (9)
  • END – Female threaded or Socket weld end
  • Branch component End Male threaded or Plain end
  • Size Range – 1/2″ – 2″ (preferred size range)
  • Rating 3000#, 6000#

Coupolet

Coupolet fittings are similar to thread end half coupling, designed for use in fire protection sprinkler systems and other low-pressure piping systems.

Olets Fittings: A Complete Guide - Make Piping Easy (10)
  • END – Female threaded end
  • Branch component or fire sprinkler End Male threaded end
  • Size Range – 1/2″ – 2″ (preferred size range)
  • Rating can be use up-to maximum of 300#
  • Thickness/Schedule 2000# 3000# and 6000#

Elbolet

An elbolet fitting is used on a 90° long radius elbow (most commonly used), short radius elbows (rare used), and can be used on 180° returns. It is typically used for instrument and thermowell connections. Elbolets fittings can be used as a drain connection, if there is not enough space to use a Weldolet. The Elbolet is available with buttweld, socket weld, and threaded end connections.

Olets Fittings: A Complete Guide - Make Piping Easy (11)
  • END – Female Threaded, Socket Weld, and Bevel end
  • Branch Pipe or Instrument End Male Threaded, Plain, and Bevel end
  • Size Range – 1/2″ – 2″ NPS (for threaded and socket weld end)
  • Size Range – Above 2″ NPS (for threaded and socket weld end)
  • Thickness/Schedule 3000# and 6000# (for socket and threaded end),
  • Rating for Buttweld end – same as piping system

Inserted Weldolet

Insert Weldolet fitting is another contoured butt-weld branch connection fitting similar to Sweepolet. But, used in less critical applications. Welding joints are easily examined by radiography, ultrasound, and other standard non-destructive techniques.

Olets Fittings: A Complete Guide - Make Piping Easy (12)
  • END – Bevel end
  • Branch Pipe End Bevel end
  • Size Range – 8″ – 24″ (mostly used size range), but the piping system should be less critical
  • Thickness/Schedule Same as the pipe/Schedule Number

Brazolet

Brazolet fittings are designed for the application with KLM and IPS brass or copper tubing. This fitting is Available with a socket or threaded end connections.

Olets Fittings: A Complete Guide - Make Piping Easy (13)

Weldolet Installation Procedure

Weldolet, Sockolet, Thredolet, Latrolet, Elbolet, Nipolet, Sweepolet, Brazolet, Coupolet (these all Fittings) are trademarks registered ® for the exclusive use of Bonney Forge.

You can get the same kind of fittings from other manufacturers, but with different name. We (the engineers) must review the fittings, as the fittings should meet the requirements of the related codes and standards.

Data Required for Ordering Branch Fittings

Manufacturer of Olets fittings, and other branch fittings are needed the following data/information to identify the required product:

  • Header or run pipe size
  • Branch or outlet pipe size
  • Branch pipe schedule (required for buttweld end connection fittings) and rating (required for socket weld and NPT threaded Olets fittings)
  • Types of Olets fittings (like: Weldolet, Thredolet, Nipolet, Sockolet, etc.)
  • MOC (Materials of Construction)

Materials of Construction

Followings are the list of most commonly used materials for Olets fittings-

  • A105 – For Carbon Steel (CS) Olets Fittings
  • A350 Gr. LF2 – For Low-Temperature Carbon Steel (LTCS)Olets Fittings
  • A182 Gr. F11, A182 Gr. F22, A182 Gr. F5, A182 Gr. F9, A182 Gr. F91, A182 Gr. F92 For Low Alloy Steel (LAS)
  • A182 Gr. F304, A182 Gr. F316, A182 Gr. F321, A182 Gr. F347 – Stainless Steel (SS)

Important Note: All the Olets Fittings are Forged Fittings

Codes and Standards

I have listed some important codes and standards below-

I hope, you got the basic and important idea about the Olets fittings. The points discussed in the above article is not limited to these points only, It can vary project to project, and as per the different practices in the industry.

Reference(s)
www.steelavailable.com
www.wermac.org
www.blog.projectmaterials.com
https://chinesefittings.en.made-in-china.com/

You may also like

A Presentation on Pipe Stress Analysis
Control Station and Control Valve in the Process Piping

Share with:


Olets Fittings: A Complete Guide - Make Piping Easy (2024)

References

Top Articles
Forgot your iPhone or iPad passcode? Here's how to reset it
Did Kendra Douglas Leave Wesh 2 News
Walb Game Forecast
Buenasado Bluewater
O'reilly's In Monroe Georgia
Endicott Final Exam Schedule Fall 2023
Scary Games 🕹️ | Play For Free on GamePix
Editado Como Google Translate
Craigslist Southern Oregon Coast
Coolmathgames.comool Math
Europese richtlijn liften basis voor Nederlandse wet - Liftinstituut - Alles voor veiligheid
True Or False Security Is A Team Effort
Pepsi Collaboration
Mid-Autumn Festival 2024: The Best Lantern Displays and Carnivals in Hong Kong 
Robertos Pizza Penbrook
5Ive Brother Cause Of Death
Arthritis Weather Index
9192464227
Craigslist Ludington Michigan
Six Oaks Rv Park Mooresburg Tn
Battlenet We Couldn't Verify Your Account With That Information
Dawat Restaurant Novi
Spinning Gold Showtimes Near Mjr Westland Grand Cinema 16
2010 Ford F-350 Super Duty XLT for sale - Wadena, MN - craigslist
Lee Lucas Jaliyah Dad
Gary Keesee Kingdom Principles Pdf
Eddie Messel Leaving 1011
Plarium Trick Or Treat
Walgreens Pharmacy On Jennings Station Road
Timon Meaning In Swahili
Statek i zarządzanie załogą w Assassin's Creed Odyssey - Assassin's Creed Odyssey - poradnik do gry | GRYOnline.pl
Free Stuff Craigslist Roanoke Va
Keci News
The Listings Project New York
Fx Channel On Optimum
7UP artikelen kopen? Alle artikelen online
How To Use DeSmuME Emulator To Play Nintendo DS Games?
Enlightenment Egg Calculator
Nina Volyanksa
JPX Studios/item asylum
Stephanie Ruhle's Husband
Paychex Mobile Apps - Easy Access to Payroll, HR, & Other Services
Priscilla 2023 Showtimes Near Regal Escondido
Pirates Bay Knaben
Madrigal Pharmaceuticals, Inc. (MDGL) Stock Forum & Discussion - Yahoo Finance
Csgo Xray Command
High Balance Bins 2023
About Data | Weather Underground
Agurahl The Butcher Wow
Fraction Button On Ti-84 Plus Ce
American Medical Response hiring EMT Basic - Bridgeport in Bridgeport, CT | LinkedIn
Latest Posts
Article information

Author: Gregorio Kreiger

Last Updated:

Views: 5735

Rating: 4.7 / 5 (77 voted)

Reviews: 92% of readers found this page helpful

Author information

Name: Gregorio Kreiger

Birthday: 1994-12-18

Address: 89212 Tracey Ramp, Sunside, MT 08453-0951

Phone: +9014805370218

Job: Customer Designer

Hobby: Mountain biking, Orienteering, Hiking, Sewing, Backpacking, Mushroom hunting, Backpacking

Introduction: My name is Gregorio Kreiger, I am a tender, brainy, enthusiastic, combative, agreeable, gentle, gentle person who loves writing and wants to share my knowledge and understanding with you.